Anya will soak the shirt later today to dissolve the transfer paper, so it’s not quite done. But here’s her Halloween kitten t-shirt. The pattern is from Urban Threads — an awesome place for hand and machine embroidery patterns.
I finished Anya’s baseball t-shirt!
I sketched a quick heart in Photoshop, and drew in two lines of baseball-style stitching. The image was printed on Transfer EZE ‘paper’ using our laser printer (which answered the question: can you laser print on this stuff?). I then took a little scrap of quilt batting and laid it on the shirt. Placed a scrap of white satin on top, then stuck the Transfer Eze print onto the satin. It adhered quite well to satin – was a little concerned!
Put it in a hoop and embroidered the red stitching to hold the whole thing in place. I then trimmed the satin about a quarter inch outside of the heart’s lines; the batting was trimmed to be about a quarter inch smaller than the satin. Finishing the project was just needle turn appliqueing the heart to the shirt (using what amounts to a really short satin stitch).
The quilt batting really enhances the stitch definition for the red lines, and it makes the whole design puff out a bit from the shirt.
I got a “magic pillowcase” kit during a pre-Christmas sale. I finally got around to making it — it’s literally a two hour project with a tiny person disrupting the process the entire time.
You lay three pieces of fabric together, roll the main body up and fold the cuff over. Pin together & stitch. Then turn it right side out and have a long piece of three fabrics – a main body, an accent strip, and a cuff. Fold it in half, and voila it looks just like a pillowcase. Fold it in half inside out (right sides together) – instead of using a French seam, I just used the serger to stitch along the bottom and side of the pillow. Knotted off the tails and it was done. Tiny person loves her pillow and blanket.
This is a pretty cool way of making pillowcases – might make some custom pillowcases for our bedroom and the guest bedroom.
Anya’s art smock is finally done! One yard of the laminated fabric (54″ wide) was enough for the interior of her owl backpack and this smock. I learnt to fold bias tape properly — unfortunately too late for this project. I had always seen it folded very carefully in half and then each raw edge folded in half toward the middle. You actually want one side to be a little longer than the other. The shorter side is stitched to the front of the fabric, folded over the raw edge, and then you top-stitch just off of the edge of the bias tape (and since the portion on the back is a little bit wider, these stitches catch the back of the fabric. The top-stitching is barely visible (depending on how well you can sew along a defined line). This should save a LOT of time applying bias tape in the future.
Anya’s backpack is done! The embroidered eyes turned out really well, and his wings flap a bit as she walks.
I think the piping turned out really well, and the side pockets work well (had a little bag of pretzels in there). I used little push button cord locks — Anya thinks they look like ladybugs. It’d be really cute if they made them in red with black dots to *really* look like ladybugs).
I moved the strap mount points – the bag didn’t sit properly when the straps were attached at the seam between the semi-circle and the rectangle. Moving the straps up to the top seam had the bag hanging nicely off her back.
I’ve finished Aisha’s dress — so we now have two completed summer dresses (just in time for the mid-February blizzards, evidently). Not much difference from before – it was pinned at the waist, and now it is stitched. I tried the top-stitching as written in the pattern (basically another line of stitching through both the skirt and the lining, maybe 1/4″ under the waist seam). I didn’t like it – it looked a little off, and it drastically impacted the drape of the fabric. I serged the hem on both dresses and like the finished look a lot better. Serging in a circle is *not* something I do well – but since the seam is sandwiched between the skirt and lining fabrics … not like anyone sees the occasional overhang on the wrapping threads.
I really like the rolled edge hem here – I found out that a nicer hem was produced on the lower end of the suggested thread tensions. Surprised me quite a bit – I thought the higher tension would make more of a roll.
And here’s the less V’d back detail – not a huge difference from Anya’s deep V, but a little bit of a different look. I really like all of the options this pattern provides. Mom purchased the add-on pattern to put sleeves on this dress too – not sure that I’d want to wear an open-backed dress in weather cold enough to warrant long sleeves … but the back is pretty easily modified to something with a zipper or buttons.
I am just starting to set up a craft room. I got the DIGNITET curtain wire from Ikea; the fabrics are wrapped around cardboard backing boards used for comic book storage. Each one is hung with two RIKTIG clips. The curtain wire holds a LOT of fabrics. Since the craft room doesn’t get much natural light, I’m not worried about fading. Dust is a concern, though. Next step is to get some containers for my yarn and thread. Anyway, here’s the craft room:
Here’s Anya’s Halloween skirt:
It’s a basic circle skirt — the circle was cut for a 23″ waist. A 4.5″ strip of fabric was then cut to 24″ and made into a 2″ wide waistband and attached to the skirt. I then ran 20″ of 2″ elastic through the band & gathered the fabric. This allows the skirt to be pulled over her head or hips. Plus it means she might be able to wear it next year 🙂
And in a bid to not have a skirt used just once, it is also her official election day skirt — blood-suckers, skeletons in the closet, ghosts/mummies/reanimated corpses (how else would dead people vote?).
Anya wants to be a flying fairy for Halloween — figured I would make her a tutu and wings for her costume. Got real tutu net and some satin for the waistband. I don’t remember where I read it, but somewhere in my research I had read that at least one layer of contrasting color should be used to add depth to the finished product. But it seemed reasonable, so I purchased a deep blue purple and a pale pinkish purple.
I found instructions at http://www.cosplayisland.co.uk/tutorials/tutu that were wonderfully detailed. I cut the strips of net, I then cut a 16″ wide strip of the net ~23″ long. Folded it in quarters so I had a 4″ wide very sturdy 23″ strip. The strips of net were gathered along a length of embroidery floss and sewn to the 4″ wide band.
I affixed the satin to the top of the net band, and then folded it over to make a waistband.
A 20″ length of 2″ wide elastic was run through the waistband and the tutu was gathered down to Anya’s waist size. This allows the waist to stretch so it is easily pulled over her hips.
And we have a tutu! Now that I am looking at it … I’m really glad I added the contrasting color layer. It doesn’t really jump out at you, but it definitely adds depth to the finished piece.
(Yes, I did tack the tutu … just not in that photo)